News articles

Details

Common Misconceptions in Mechanical Lubrication and Sealing

Construction machinery is often operated at construction sites with relatively harsh environments. After being used for a period of time, construction machinery should undergo necessary maintenance and upkeep to maintain the equipment in a good technical condition. In the equipment's operation manual, there are generally detailed requirements for lubricating oil filling at each lubrication point, and the sealing rings must be replaced in a timely manner once they are worn. However, surveys on actual usage conditions have found that some operators and maintenance personnel often ignore the above requirements. Several common incorrect practices are as follows:

 

1¡¢Do we need to lubricate it?

Just add a little oil! Due to differences in the working methods and operating conditions of various parts of the equipment, there are strict requirements for the oil-filling interval, the amount of oil added each time, and the filling method for each lubrication point. Operators and maintenance personnel must strictly follow these requirements and must not simply add a small amount of oil randomly. Such a casual approach cannot meet the lubrication needs.

 

2¡¢We already added oil to it¡ªcan it still be under-lubricated?

Different moving parts of the equipment, different working methods, and varying ambient temperatures all result in different requirements for lubricants. It is necessary to add lubricants of different types and grades in accordance with the specifications. Only by using lubricants that contain necessary additives and meet the required physical and chemical indicators can the equipment achieve proper lubrication. Randomly adding oil without checking the grade will lead to problems.

 

3¡¢Adding more lubricating oil can¡¯t hurt!

The structural type and operating conditions of the equipment¡¯s moving parts determine the appropriate amount of oil to be added, and specific regulations and requirements for this are usually clearly stated in the equipment¡¯s operation manual. Maintenance personnel should add an appropriate amount of lubricating oil based on the operation manual, as well as the oil level indicators, dipsticks, or sight glasses equipped on the equipment. Adding an excessive amount of lubricating oil does more harm than good.

 

4¡¢After adding lubricating oil, the work gets done faster!

Strictly speaking, this is a misunderstanding rooted in incorrect conceptual understanding. Only fuel directly contributes to power generation (or "does work" in mechanical terms). Adding lubricating oil generally refers to applying it between the moving friction pairs. The oil fills in the uneven surfaces (of the friction pairs) and maintains an oil film of a certain thickness, which serves to separate the two contacting surfaces of the friction pairs. This achieves the goals of reducing frictional resistance and minimizing wear, while also providing cooling for machine components and sealing effects. These functions of lubricating oil indirectly support the fuel in generating power (or "doing work").

 

5¡¢It¡¯s leaking oil¡ªjust replace the sealing ring!

In a hydraulic system, oil leakage faults are mostly caused by sealing ring failure. Sealing rings achieve a sealing effect through elasticity (pressure). After a sealing ring is properly installed, its elasticity should apply a preload to the contact surface when there is no oil pressure¡ªspecifically, its cross-section must have a certain degree of compressive deformation. When oil pressure is applied, the ring is pressed against one side of the groove, and it achieves the sealing effect through elasticity and other factors.

 

5¡¢The sealing ring model is correct¡ªjust slip it on!

When replacing a sealing ring, the opened parts of the hydraulic system must first be thoroughly cleaned, and strict precautions must be taken to prevent impurities or contaminated oil from entering the system. During installation, it is best to use specialized tools to avoid scratching the sealing ring with sharp metal edges or even fingernails.

 

7¡¢Spare sealing rings¡ªjust store them anywhere!

Since sealing rings contain a relatively large number of additives, they are prone to aging and deterioration. Therefore, during storage, it is necessary to not only avoid exposure to sunlight but also prevent them from getting damp and overheated. Additionally, care must be taken to ensure they do not come into contact with acidic or alkaline substances. Generally, the storage period should not exceed 18 months. It is not allowed to string them together with ropes, iron wires, or similar items for hanging storage. Thus, it is improper to store spare sealing rings casually.

 

8¡¢The oil is dirty¡ªjust pour it out!

Except for hydraulic oil that has become rancid and deteriorated, a large amount of other hydraulic oil and lubricating oil can still be reused. Specifically, hydraulic oil contaminated only with metal particles can be reused after sedimentation and filtration. For oil with severe contamination, after simple treatment, it can be used for lubricating rough machining equipment, preventing rust on outdoor equipment, or collected and handed over for waste oil recycling. Such practices help save energy and reduce waste. In contrast, the approach of "pouring it out and being done with it" (or "disposing of it by simply pouring it away") may be convenient, but it pollutes the environment and violates the principles of sustainable development.


£¨+86£©138-4494-4528

53-3 Honghai Road, Yuhong District, Shenyang City, Liaoning Province, China

Navigation

Mobile official website

Copyright @ 2023 .  Shenyang Fente Mining Machinery Co., Ltd .  All rights reserved.   |   ÁÉICP±¸2023009852ºÅ-1

Technical Support£º ÐÅÍø¿Æ¼¼ | Admin Login
seo seo