News articles

Details

Typical faults of hydraulic cone crusher

Compared with traditional crushers such as jaw crushers and impact crushers, hydraulic cone crushers have a much more complex structure, more precise coordination, and higher processing requirements. At the same time, their hydraulic and lubrication systems are also very complex. Once a malfunction occurs, the machine needs to be shut down for maintenance, which can have an impact on production.

Below are 7 typical faults of hydraulic cone breakage, so that you can quickly find the cause and solve the problem accordingly.

1. Adjusting ring runout

The adjustment ring runout refers to the abnormal runout of the part above the adjustment ring during the crushing operation of the multi cylinder crusher and continuous impact on the frame. There are two main reasons for its occurrence:

¢Ù Overload. The powder in the feed is too much and wet, with excessive viscosity, which blocks the crushing chamber and cannot be discharged normally, resulting in overload; The adjustment of the ore discharge port is too small, which is not suitable for the current hardness and size of the material, resulting in overload.

¢Ú Insufficient release cylinder pressure. According to Newton's third law, the pressure of the release cylinder actually determines the maximum breaking force of the crusher. When the pressure of the release cylinder is insufficient, the maximum breaking force decreases, and the continuous occurrence of ring skipping is actually the continuous occurrence of abnormal factors such as over iron or overload protection.

2. Eccentric sleeve/moving cone liner ablation

Eccentric sleeve erosion is a common and serious fault in multi cylinder cone breaking. Eccentric sleeve is a direct contact component that drives the dynamic cone to perform rotary swing crushing motion. As long as the crusher is working, the eccentric sleeve will rub against the dynamic cone liner with high strength. Therefore, only by ensuring sufficient lubrication can they avoid erosion. Therefore, once this fault occurs, it is inevitable that there is a problem with lubrication, which may be due to oil leakage, blocked lubrication pipelines, or insufficient lubrication pressure.

3. Fixed cone loosening

Loosening the fixed cone can greatly affect the crushing effect, and allowing it to develop can greatly damage the crusher, even leading to direct scrapping. The reasons for loosening the fixed cone are as follows:

¢Ù The thread wear of the adjusting ring and the fixed cone fitting prevents them from engaging and locking properly;

¢Ú The crusher performs crushing operations when the locking cylinder pressure is insufficient;

¢Û The lining plate of the moving cone or the fixed cone is too thick, so that the thread engagement between the fixed cone and the adjusting ring is insufficient under the same mining outlet.

¢Ü The discharge port is too large, resulting in insufficient engagement between the fixed cone and the adjusting ring thread.

4. Drive shaft sleeve ablation

The drive shaft bushing is the sliding bearing of the drive shaft, which bears the high-speed and high-strength rotational friction of the drive shaft at around 800RPM. If the lubrication is not in place, it will generate a huge accumulation of heat in a short period of time, leading to the occurrence of sleeve burning failure. The main cause of the occurrence is also insufficient lubrication, lubricating oil leakage or blockage of the transmission shaft lubricating oil circuit.

5. Material particle pollution lubrication system

Many parts of the multi cylinder hydraulic cone crusher that require lubrication are made of copper alloy material, which is relatively soft in texture. At the same time, they are also very important, and the cleanliness of the lubricating oil needs to be guaranteed. Therefore, crushers also have high requirements for sealing, and under normal circumstances, external dust will not enter the interior of the crusher. Possible reasons include: malfunction of the transmission axle box blower, malfunction of the lubrication system breather, broken seal of the oil storage tank cover plate, damage to the transmission shaft or dynamic cone sealing ring, etc.

6. Lubricating oil leakage

The lubrication system can be said to be the lifeline for ensuring the long-term stable operation of multi cylinder hydraulic cone crushers. Once the lubricating oil is insufficient, it can cause a series of serious crusher failures. Lubricating oil leakage is a very common fault in the actual operation of crushers, and the causes are as follows:

¢Ù The lubrication pipeline of the crusher is damaged by material erosion due to long-term bending or improper protection, resulting in lubricating oil leakage;

¢Ú Loose lubrication pipeline interfaces on the crusher due to collision or vibration;

¢Û The T-shaped U-shaped sealing ring inside the crusher is damaged, the sealing O-ring of the transmission part is ineffective, or the sealing of the lubrication station is ineffective.

7. Excessive vibration

Excessive vibration of the crusher can affect the stability and safety of the crushing worktable, especially the steel structure worktable. At the same time, severe vibration can cause many connecting parts, transmission parts, and joint pipelines to loosen, leading to other faults. The reasons for excessive vibration include:

¢Ù Worn counterweights or protective plates, unbalanced rotation;

¢Ú The tooth root clearance between the large umbrella gear and the transmission small gear is incorrect, resulting in improper gear meshing;

¢Û Bending of the transmission shaft or excessive rotation speed of the transmission shaft;

¢Ü The foundation of the crusher is unbalanced and the bearing capacity is imbalanced.

In addition to paying attention to the maintenance and repair of cone breakage in production to reduce the failure rate, we should also be more careful when purchasing equipment and choose manufacturers with guaranteed equipment quality.

£¨+86£©138-4494-4528

53-3 Honghai Road, Yuhong District, Shenyang City, Liaoning Province, China

Navigation

Mobile official website

Copyright @ 2023 .  Shenyang Fente Mining Machinery Co., Ltd .  All rights reserved.   |   ÁÉICP±¸2023009852ºÅ-1

Technical Support£º ÐÅÍø¿Æ¼¼ | Admin Login
seo seo